Cleaning is a process that can feel like an arduous task, but with this guide to cleaning your Winchester 30-30 Lever Action rifle, you’ll be able to take care of it in no time!
How to Clean
If you have a Winchester 30 30 lever action rifle, you will need to periodically clean it. To clean the gun, first make sure that the weapon is unloaded. Then you will need to remove the barrel,action, and stock. Next, you will need to loosen all of the screws holding the metal parts together. Finally, you can plunge the weapon into a tub of hot water and soap and scrub everything clean. After cleaning, make sure to dry the weapon completely before reassembling it.
The Proper METHODS of cleaning the Winchester 30 30 Lever Action
When it comes to rifles, Winchester is one of the brands that many people know and trust. One of the reasons why is because their rifles are very easy to clean. In this guide, we are going to teach you how to clean a Winchester 30 30 lever action rifle the right way.
Before starting, you will need some common cleaning supplies, such as a solvent, a brass brush, patches, and a cleaning rod. You also need to have a jag or pipe cleaner for cleaning inside the barrel. Make sure to have plenty of ammo and bullets too in case you have to clean the rifle in cold weather.
To begin washing your rifle, take off the bolt and magazine. Make sure that all debris is removed before putting them back on. Then wash your entire rifle with a solvent such as Birchwood Casey Gun Scrubber® Super Solvent 60%. After washing it off with water, dry it off with patches and use a brass brush to scrub any remaining dirt and grime. If necessary, use a jag or pipe cleaner to get into the tight areas. Finally, put everything back together and enjoy your clean and shiny Winchester 30 30 lever action!
What is The Proper METHODS of cleaning the Winchester 30 30 Lever Action?
Cleaning a Winchester 30 30 Lever Action can be a little daunting, but it doesn’t have to be. There are many ways to clean your rifle, and the most important thing is to use the proper method for the type of firearm you are cleaning. Here are some steps that you can take to clean your rifle:
-Wash the weapon with warm water and a mild soap.
-Use a gun barrel brush to scrub down the barrel.
-Rinse the weapon and dry it completely.
-Apply a quality firearm oil to the metal parts of the weapon.
Frequenty Asked Questions
How Do I Clean A Winchester 30 30 Lever Action?
You have to remove the action from the rifle.
For this gun, a good bet would be to try our exclusive gun cleaner while you are at home. This is only one option and not the only way that this gun could be cleaned. It might also be a good idea to invest in a muzzle-loader bore brush, of course.
How Do I Clean My Winchester 30 30 Lever Action Rifle?
Apply a thin coat of oil over the metal and the metal parts with a cloth. Next, from the muzzle to the bolt handle, use a bore guide to remove any residue inside of the barrel. Use duck-tape or brass wool to polish out any rough spots in the metal.
First, run a piece of cloth through the barrel, then use some gun oil to wipe all the metal parts. Spray it with some WD-40 and let it sit for a few minutes before wiping off any excess oil. Then, use all purpose cleaner (like, dish soap) to wash out any built up grime. Finally, if you have time, place the rifle back in its storage case and allow it to dry overnight in your safe place.
I Bought A Winchester 30 30 Lever Action And Want To Clean It. How Do I Clean A Winchester 30 30 Lever Action?
Before you try to clean the Winchester 30 30 Lever Action, do not use any water to get it wet and don’t allow any water to get into the muzzle. Use a very small amount of mild soap and hot water. If you are using a straw, make sure that it’s not pointed at you. Then, use a brush for just the outside and ensure that there is no soap or gunky residue left behind. Note: Results may vary based on how dirty your firearm is.
Remove the barrel from the receiver and wipe it down with a rag or cloth soaked in CLP. Wipe down all surfaces of the rifle, including inside of the receiver where you can see right through it. Apply a nickel-sized, circular dab of lube to the bolt lock carrier, which is just forward of the action hinge on the left side where you can see it when your rifle is open. Screw in an empty speed loader in that location with your thumbs to dislodge any dirt or grit that might be present. Remove the magazine, fill each chamber with light oil (or CLP), close and open the action several times to make sure everything is properly coated and then screw in a new speed loader.
I Have A Winchester 30 30 Lever Action Rifle, How Should I Clean It?
You should wipe it down thoroughly, especially any wood parts and the lever handle, with a damp cloth and let dry. Then use a soft cloth or Q-tip to clean out the barrel and chamber. Now you should oil 10-40 rounds of ammunition and wipe each round down with a cotton swab or tissue paper.
To clean your weapon, first remove the barrel by removing the hinge pin. Then take a small screwdriver and remove the three screws in the iron sight. After that, you will want to remove all other screws on the rifle while it is completely disassembled. Next, you’ll want to take a Q-Tip and some solvent and clean balls until they are shiny. For debris, use some brushes to scrub them with cleaning fluid and a toothbrush to scrub them with solvent until they come off easy. Finally, just reassemble your rifle back together with all of the parts in the correct order, oiling it with CLP before doing so.
How Do I Disassemble And Reassemble My Lever Action Rifle?
We recommend assembling your rifle with a new magazine before disassembling and reassembling it. When you are ready to disassemble the gun, hold the slide release lever outward with your right hand and pull the slide back slightly with your left hand. Now use your right hand to push up on the front of the frame beyond the receiver and remove the magazine. Reinserting a magazine is not necessary for this step. After loading a new magazine, do not assemble any part of your rifle until you are ready to fire it again.
Your lever action rifle should come with directions, but if you need help finding the instructions there is a link below the pictures. This article shows how to disassemble and reassemble a lever action rifle.
How To Clean A Winchester Lever Action Rifle?
For the best results, used a soft cloth and a solvent to remove residue from your Winchester. For oil-based stains, use mineral spirits or turpentine.
The best way to clean a lever action rifle is to remove the buttstock, then soak the gun in soapy water. Spray water onto the bore and chamber with a trigger guard open. Pull the bolt back and use a brush to scrub the inside of the firing chamber. Dip a cloth in wet jugs and dry out the outside of weapon.